HEM灰分測定儀
灰分測定儀產品詳細介紹：
一、灰分測定儀設備特點：
1）升溫快 由100℃升溫指1000℃，小于30分鐘
2）灰化快 作灰化爐用時，可開進出風孔，加煙筒，有利于補進新鮮氧氣，加速灰化
3）重量輕 6升爐型爐體僅重52公斤
4）節能性好 6升爐型采用16A/200V
5）熱污染少 由于新型材料絕熱性好，升溫至1000℃，并保持1小時后，外殼表面不燙手 （約60℃）
6）恒溫時控 各工步溫度升到設定值后，定時器自動開始工作，按設定時間保持恒溫
7）控溫精密 具備多種溫控器可供選擇，進入保持狀態后，溫度波動小/采用P 型多工步溫控器，各工步溫度升溫斜率均可預置
8）實用安全 具有開門自動斷電功能，使用非常安全
二、高溫?zé)鉅t技術參數
控制方式 | 單點程控 |
適用電源 | AC 200V |
工步數 | 1 |
溫度穩定性（滿量程） | 1％FS |
定時設定范圍 | 999min |
三、高溫?zé)鉅t溫度控制器技術參數
爐型 | 6L |
溫度上升時間 | 100-1000℃<30min |
電源類型 | AC 200V 16A |
功率（KW） | 2 |
發熱體類型 | 電阻絲 |
傳感器類型 | K |
爐腔尺寸W×D×H | 200×250×120mm |
爐體尺寸W×D×H | 550×530×430mm |
凈重（kg） | 52 |
Burn on high temperature furnace
Burn on high temperature furnace products detail says:
A furnace equipment, high temperature burning solutions:
1) warming faster by 100 ℃ temperature 1000 ℃, less than 30 minutes
2) quick ashing as ashing furnace, can into the wind hole, pipe, is conducive to fill in fresh oxygen, accelerate ashing
3) light weight 6 litres of furnace type furnace only 52 kg
4) good energy-saving type 6 litres of furnace using 16 a / 200 v
5) thermal pollution due to less new materials good insulation, heat up to 1000 ℃, and keep an hour later, the shell surface is not hot (about 60 ℃)
6) thermostatic control each step after the temperature reaches the set value, the timer automatically start to work, according to the set time constant temperature
7) precision of temperature control with multiple thermostat to choose from, after entering the maintain state, temperature fluctuations for small/P type step multiplex temperature controller, each step working temperature ramp rate can be preset
8) practical security has open the door automatically power off function, use very safe
Second, the high temperature burning furnace temperature controller parameters
The control mode
A single point of SPC
Applicable to the power supply
AC 200 v
Work steps
1
Temperature stability (full scale)
1% FS
Time setting range
999 min
3, high temperature burning furnace technical parameters
